Reliability of the color measurement of resin composites using images obtained using a stereoscopic loupe.

This study assessed the reliability of a color measurement method using images obtained from a charge-coupled device (CCD) camera and a stereoscopic loupe. Disc-shaped specimens were created using the composite Filtek Z350 XT (shades DA1, DA2, DA3, and DA4) (n = 3). CIELAB color coordinates of the specimens were measured using the spectrophotometer SP60 over white and black backgrounds. Images of the same specimens were taken using a CCD camera attached to a stereoscopic loupe. The color of the image was measured (red-green-blue [RGB]) using an image processing software and converted to CIELAB coordinates. For each color coordinate, data from images were adjusted using linear regressions predicting those values from SP60. The whiteness index for dentistry (WID) and translucency parameter (TP00) of the specimens as well as the color differences (ΔE00) among pairwise shades were calculated. Data were analyzed via repeated-measures analysis of variance and Tukey's post hoc test (α = 0.05). Images obtained using the loupe tended to be darker and redder than the actual color. Data adjustment resulted in similar WID, ΔE00, and TP00 values to those observed for the spectrophotometer. Differences were observed only for the WID of shade DA3 and ΔE00 for comparing DA1 and DA3 over the black background. However, these differences were not clinically relevant. The use of adjusted data from images taken using a stereoscopic loupe is considered a feasible method for color measurement.

Detection of Maize Mold Based on a Nanocomposite Colorimetric Sensor Array under Different Substrates.

This study developed a novel nanocomposite colorimetric sensor array (CSA) to distinguish between fresh and moldy maize. First, the headspace solid-phase microextraction gas chromatography-mass spectrometry (HS-SPME-GC/MS) method was used to analyze volatile organic compounds (VOCs) in fresh and moldy maize samples. Then, principal component analysis and orthogonal partial least-squares discriminant analysis (OPLS-DA) were used to identify 2-methylbutyric acid and undecane as key VOCs associated with moldy maize. Furthermore, colorimetric sensitive dyes modified with different nanoparticles were employed to enhance the dye properties used in the nanocomposite CSA analysis of key VOCs. This study focused on synthesizing four types of nanoparticles: polystyrene acrylic (PSA), porous silica nanospheres (PSNs), zeolitic imidazolate framework-8 (ZIF-8), and ZIF-8 after etching. Additionally, three types of substrates, qualitative filter paper, polyvinylidene fluoride film, and thin-layer chromatography silica gel, were comparatively used to fabricate nanocomposite CSA combining with linear discriminant analysis (LDA) and K-nearest neighbor (KNN) models for real sample detection. All moldy maize samples were correctly identified and prepared to characterize the properties of the CSA. Through initial testing and nanoenhancement of the chosen dyes, four nanocomposite colorimetric sensitive dyes were confirmed. The accuracy rates for LDA and KNN models in this study reached 100%. This work shows great potential for grain quality control using CSA methods.

Multiplex nanozymatic biosensing of Salmonella on a finger-actuated microfluidic chip.

A colorimetric biosensor was elaboratively designed for fast, sensitive and multiplex bacterial detection on a single microfluidic chip using immune magnetic nanobeads for specific bacterial separation, immune gold@platinum palladium nanoparticles for specific bacterial labeling, a finger-actuated mixer for efficient immunoreaction and two coaxial rotatable magnetic fields for magnetic nanobead capture (outer one) and magnet-actuated valve control (inner one). First, preloaded bacteria, nanobeads and nanozymes were mixed through a finger actuator to form nanobead-bacteria-nanozyme conjugates, which were captured by the outer magnetic field. After the inner magnetic field was rotated to successively wash the conjugates and push the H2O2-TMB substrate for resuspending these conjugates, colorless TMB was catalyzed into blue TMBox products, followed by color analysis using ImageJ software for bacterial determination. This simple biosensor enabled multiplex Salmonella detection as low as 9 CFU per sample in 45 min.

Chip-based automated equipment for dual-mode point-of-care testing foodborne pathogens.

Foodborne pathogens have a substantial bearing on food safety and environmental health. The development of automated, portable and compact devices is essential for the on-site and rapid point-of-care testing (POCT) of bacteria. Here, this work developed a micro-automated microfluidic device for detecting bacteria, such as Escherichia coli (E. coli) O157:H7, using a seashell-like microfluidic chip (SMC) as an analysis and mixing platform. The automated device integrates a colorimetric/fluorescent system for the metabolism of copper (Cu2+) by E. coli affecting o-phenylenediamine (OPD) for concentration analysis. A smartphone was used to read the RGB data of the chip reaction reservoir to detect colorimetric and fluorescence patterns in the concentration range of 102-106 CFU mL-1. The automated device overcomes the low efficiency and tedious steps of traditional detection and enables high-precision automated detection that can be applied to POCT in the field, providing an ideal solution for broadening the application of E. coli detection.

Synthesis of a COF-on-MOF hybrid nanomaterial for enhanced colorimetric biosensing.

The construction of hybrid materials is significant for the exploration of functionalities in colorimetric biosensing due to its structural designability and synergy effects. In this work, a COF-on-MOF hybrid nanomaterial has been newly synthesized for colorimetric biosensing. Experimental results reveal that on-surface synthesis of COF on MOF brings nanoscale proximity between COF and MOF, which exhibits more than two folds of peroxidase-like activity as compared to single Fe-MOF. Therefore, by using the MCA@Fe-MOF nanomaterial with the assist of a specific acetyl-peptide, MCA@Fe-MOF can serve as an efficient signal reporter for colorimetric assay of histone deacetylase (HDAC), and the limit of detection (LOD) can be as low as 0.261 nM. Looking forward, the demand for diverse and promising COF-on-MOF nanomaterials with varied functionalities is anticipated, propelling further exploration of their role in colorimetric biosensing.

Asymmetrically split DNAzyme-based colorimetric and electrochemical dual-modal biosensor for detection of breast cancer exosomal surface proteins.

Exosomal surface proteins are potentially useful for breast cancer diagnosis and awareness of risk. However, some detection techniques involving complex operations and expensive instrumentation are limited to advance to clinical applications. To solve this problem, we develop a dual-modal sensor combining naked-eye detection and electrochemical assay of exosomal surface proteins from breast cancer. Most of existing sensors rely on aptamers recognizing exosomes and generating amplified signals at the same time, which require well-designed aptamer probes to avoid difficulties in identifying exosomes. In our work, aptamers not bound by the exosomes can serve as complete templates to induce formation of G quadruplexes. The peroxidase activity of the G-quadruplex/hemin DNAzyme catalyze substrates can generate both color and electrochemical signals. The developed dual-modal sensor offers a remarkable capability to differentiate nonmetastatic, metastatic breast cancer patients, and healthy individuals through the analysis of exosomal surface proteins. The sensor's distinctive features, including its universality, simplicity, and cost-effectiveness, position it as a promising diagnostic tool in breast cancer research and clinical practice.

Tetralactam macrocycle based indicator displacement assay for colorimetric and fluorometric dual-mode detection of urinary uric acid.

An indicator displacement assay for colorimetric and fluorometric dual-mode detection of urinary uric acid (UA) was constructed using a water-soluble naphthalene-based tetralactam macrocycle and the phenoxazine dye, resorufin (RF). The visual detection of UA levels of volunteers was successfully realized using modified paper assays, which could be used for the home monitoring of urinary UA.

A highly sensitive sensor for colorimetric detection of palladium(II) in lysosomes and its applications.

Considering the scarcity of palladium ion probes with subcellular organelle targeting, especially probes with near-infrared (NIR) emission wavelength fluorophores, our group has been working to overcome this problem and looking forward to providing potential practical tools for exploring the toxicity of palladium ions at the subcellular level. In this paper, a novel colorimetric and NIR fluorescent probe, BHCy-Pd, for the specific detection of palladium ions (Pd2+) in lysosomes via an internal charge-transfer (ICT) mechanism was designed and synthesized. As expected, BHCy-Pd exhibited a rapid, selective, and sensitive response for palladium with an ultralow limit of detection at 5.9 nM, accompanied by a distinct color change from purple to blue. Furthermore, BHCy-Pd can be made into a simple test strip for rapid and easy detection of Pd2+ in practical applications. Importantly, BHCy-Pd is capable of specific distribution in lysosomes, and thus can detect Pd2+ in real-time, thereby providing a potential tool for studying the cytotoxicity of Pd2+ ions at the subcellular level.

Rapid fluorescent color analysis of copper ions on a smart phone via ratiometric fluorescence sensor.

A smartphone-assisted fluorescence color sensing system for rapid, convenient, and on-site detection of copper ions was developed. The ratiometric fluorescence sensor was fabricated by using silica-coated blue-light-emitting carbon dots and surface-grafted red-light-emitting cadmium-telluride quantum dots. After exposure to Cu2+ in 20 s, the red fluorescence was quenched obviously, while the blue fluorescence remained unchanged, and the sensor color changes continuously from red to blue under the ultraviolet lamp. The concentration (50-1200 nM) of copper ions could be measured by the fluorescence spectrum (excitation at 360 nm, dual-emission at 441 and 640 nm) with a detection limit of 7.7 nM. The fluorescence colors were converted to digital RGB values to calculate the concentration of copper ions by a smartphone with a detection limit of 9.6 nM. The method was applied to detecting copper ions spiked in real samples with recovery from 97.9 to 108.0% and RSD from 3.8 to 8.9%. Thus, this convenient and practical fluorescence color sensing system presents a new strategy for rapid, sensitive, and on-site determination of copper ions in environmental or biological samples.

Ratiometric fluorescence and colorimetric dual-mode sensing platform based on carbon dots for detecting copper(II) ions and D-penicillamine.

A sensing platform with both ratiometric fluorescence and colorimetric responses towards copper(II) ions (Cu2+) and D-penicillamine (D-pen) was constructed based on carbon dots (CDs). o-Phenylenediamine (OPD) was employed as a chromogenic development reagent for reaction with Cu2+ to generate the oxidation product 2,3-diaminophenazine (oxOPD), which not only emits green fluorescence at 555 nm, but also quenches the blue fluorescence of CDs at 443 nm via the inner filter effect (IFE) and Förster resonance energy transfer (FRET). Additionally, oxOPD exhibits obvious absorption at 420 nm. Since the intense chelation affinity of D-pen to Cu2+ greatly inhibits the oxidation of OPD, the intensity ratio of fluorescence at 443 nm to that at 555 nm (F443/F555) and the absorbance at 420 nm (A420) were conveniently employed as spectral response signals to represent the amount of D-pen introduced into the testing system. This dual-signal sensing platform exhibits excellent selectivity and sensitivity towards both Cu2+ and D-pen, with low detection limits of 0.019 µM and 0.092 µM, respectively. In addition, the low cytotoxicity of the testing reagents involved in the proposed sensing platform facilitates its application for live cell imaging.

Target-Responsive Smart Nanomaterials via a Au-S Binding Encapsulation Strategy for Electrochemical/Colorimetric Dual-Mode Paper-Based Analytical Devices.

Target-responsive nanomaterials attract growing interest in the application of drug delivery, bioimaging, and sensing due to the responsive releasing of guest molecules by the smart molecule gate. However, it remains a challenge to develop smart nanomaterials with simple assembly and low nonspecific leakage starting from encapsulation strategies, especially in the sensing field. Herein, Au nanoclusters (Au NCs) were first grown on porous carbon derived from ZIF-8 (PCZIF) to be employed as nanocarriers. By employing the Au NCs as linkers and aptamer (Apta) double-strand hybrids (target Apta and SH-complementary DNA) as capping units, we reported the novel target-responsive nanomaterials of Apta/Au NCs-PCZIF/hemin through Au-S binding encapsulation for sensing assays. The Au-S binding encapsulation strategy simplified the packaging procedure and reduced non-target responsive leakage. As a proof, ochratoxin A (OTA) as a model target participates in the double-strand hybrid competitive displacement reaction and triggered Apta conformation switches from a coil to a G-quadruplex structure accompanied by the dissociation of the gatekeeper. Simultaneously, the released hemin can initiate a self-assembly to form G-quadruplex/hemin DNAzyme. Interestingly, owing to DNAzyme providing electron transfer mediators and peroxidase-like activity, we proposed an electrochemical/colorimetric dual-mode paper-based analytical device (PAD) that provided self-verification to enhance reliability and accuracy, benefiting from independent signal conversion and transmission mechanism. As a consequence, the proposed dual-mode PAD could achieve sensitive electrochemical detection and visual prediction of OTA in the range of 1 pg/mL to 500 ng/mL and 50 pg/mL to 500 ng/mL, respectively. The electrochemical detection limit for OTA was as low as 0.347 pg/mL (S/N = 3). We believe that this work provides point-of-care testing (POCT) tools for a broad spectrum of applications.

Advanced graphene oxide-based paper sensor for colorimetric detection of miRNA.

MicroRNAs (miRNAs), found in blood and body fluids, have emerged as potential non-invasive biomarkers for disease and injury. miRNAs are quantitatively evaluated using typical RNA analysis methods such as the quantitative reverse transcription polymerase chain reaction, microarrays, and Northern blot, all of which require complex procedures and expensive reagents. To utilize miRNAs as practical biomarkers, it will be helpful to develop simple and user-friendly sensors. In this study, a paper-based miRNA sensor was developed by combining two methods: (1) target-recycled DNAzyme (Dz) amplification and (2) graphene oxide-assisted Dz blotting on paper. The Dz spots on paper caused a miRNA-dependent color change in presence of colorimetric reagents and facilitated the quantification of absolute amount of the target miRNA, irrespective of the volume, with high reproducibility. This approach is technologically straightforward and enables quantification of as low as 7.75 fmol miRNA using a portable smartphone.

Design of a High-Sensitivity Dimeric G-Quadruplex/Hemin DNAzyme Biosensor for Norovirus Detection.

G-quadruplexes can bind with hemin to form peroxidase-like DNAzymes that are widely used in the design of biosensors. However, the catalytic activity of G-quadruplex/hemin DNAzyme is relatively low compared with natural peroxidase, which hampers its sensitivity and, thus, its application in the detection of nucleic acids. In this study, we developed a high-sensitivity biosensor targeting norovirus nucleic acids through rationally introducing a dimeric G-quadruplex structure into the DNAzyme. In this strategy, two separate molecular beacons each having a G-quadruplex-forming sequence embedded in the stem structure are brought together through hybridization with a target DNA strand, and thus forms a three-way junction architecture and allows a dimeric G-quadruplex to form, which, upon binding with hemin, has a synergistic enhancement of catalytic activities. This provides a high-sensitivity colorimetric readout by the catalyzing H2O2-mediated oxidation of 2,2'-azino-bis(3-ethylbenzothiazoline -6-sulfonic acid) diammonium salt (ABTS). Up to 10 nM of target DNA can be detected through colorimetric observation with the naked eye using our strategy. Hence, our approach provides a non-amplifying, non-labeling, simple-operating, cost-effective colorimetric biosensing method for target nucleic acids, such as norovirus-conserved sequence detection, and highlights the further implication of higher-order multimerized G-quadruplex structures in the design of high-sensitivity biosensors.

Portable on-chip colorimetric biosensing platform integrated with a smartphone for label/PCR-free detection of Cryptosporidium RNA.

Cryptosporidium, a protozoan pathogen, is a leading threat to public health and the economy. Herein, we report the development of a portable, colorimetric biosensing platform for the sensitive, selective and label/PCR-free detection of Cryptosporidium RNA using oligonucleotides modified gold nanoparticles (AuNPs). A pair of specific thiolated oligonucleotides, complementary to adjacent sequences on Cryptosporidium RNA, were attached to AuNPs. The need for expensive laboratory-based equipment was eliminated by performing the colorimetric assay on a micro-fabricated chip in a 3D-printed holder assembly. A smartphone camera was used to capture an image of the color change for quantitative analysis. The detection was based on the aggregation of the gold nanoparticles due to the hybridization between the complementary Cryptosporidium RNA and the oligonucleotides immobilized on the AuNPs surface. In the complementary RNA's presence, a distinctive color change of the AuNPs (from red to blue) was observed by the naked eye. However, in the presence of non-complementary RNA, no color change was observed. The sensing platform showed wide linear responses between 5 and 100 µM with a low detection limit of 5 µM of Cryptosporidium RNA. Additionally, the sensor developed here can provide information about different Cryptosporidium species present in water resources. This cost-effective, easy-to-use, portable and smartphone integrated on-chip colorimetric biosensor has great potential to be used for real-time and portable POC pathogen monitoring and molecular diagnostics.

Paper-based lateral flow assay using rhodamine B-loaded polymersomes for the colorimetric determination of synthetic cannabinoids in saliva.

Synthetic cannabinoids are one of the many substances of abuse widely spreading in modern society. Medical practitioners and law enforcement alike highly seek portable, efficient, and reliable tools for on-site detection and diagnostics. Here, we propose a colorimetric lateral flow assay (LFA) combined with dye-loaded polymersome to detect the synthetic cannabinoid JWH-073 efficiently. Rhodamine B-loaded polymersome was conjugated to antibodies and fully characterized. Two LFA were proposed (sandwich and competitive), showing a high level of sensitivity with a limit of detection (LOD) reaching 0.53 and 0.31 ng/mL, respectively. The competitive assay was further analyzed by fluorescence, where the LOD reached 0.16 ng/mL. The application of the LFA over spiked synthetic saliva or real human saliva demonstrated an overall response of 94% for the sandwich assay and 97% for the competitive LFA. The selectivity of the system was assessed in the presence of various interferents. The analytical performance of the LFA system showed a coefficient of variation below 6%. The current LFA system appears as a plausible system for non-invasive detection of substance abuse and shows promise for synthetic cannabinoid on-site sensing.

On-farm colorimetric detection of Pasteurella multocida, Mannheimia haemolytica, and Histophilus somni in crude bovine nasal samples.

This work modifies a loop-mediated isothermal amplification (LAMP) assay to detect the bovine respiratory disease (BRD) bacterial pathogens Pasteurella multocida, Mannheimia haemolytica, and Histophilus somni in a colorimetric format on a farm. BRD causes a significant health and economic burden worldwide that partially stems from the challenges involved in determining the pathogens causing the disease. Methods such as polymerase chain reaction (PCR) have the potential to identify the causative pathogens but require lab equipment and extensive sample processing making the process lengthy and expensive. To combat this limitation, LAMP allows accurate pathogen detection in unprocessed samples by the naked eye allowing for potentially faster and more precise diagnostics on the farm. The assay developed here offers 66.7-100% analytical sensitivity, and 100% analytical specificity (using contrived samples) while providing 60-100% concordance with PCR results when tested on five steers in a feedlot. The use of a consumer-grade water bath enabled on-farm execution by collecting a nasal swab from cattle and provided a colorimetric result within 60 min. Such an assay holds the potential to provide rapid pen-side diagnostics to cattle producers and veterinarians.

Colorimetric histology using plasmonically active microscope slides.

The human eye can distinguish as many as 10,000 different colours but is far less sensitive to variations in intensity1, meaning that colour is highly desirable when interpreting images. However, most biological samples are essentially transparent, and nearly invisible when viewed using a standard optical microscope2. It is therefore highly desirable to be able to produce coloured images without needing to add any stains or dyes, which can alter the sample properties. Here we demonstrate that colorimetric histology images can be generated using full-sized plasmonically active microscope slides. These slides translate subtle changes in the dielectric constant into striking colour contrast when samples are placed upon them. We demonstrate the biomedical potential of this technique, which we term histoplasmonics, by distinguishing neoplastic cells from normal breast epithelium during the earliest stages of tumorigenesis in the mouse MMTV-PyMT mammary tumour model. We then apply this method to human diagnostic tissue and validate its utility in distinguishing normal epithelium, usual ductal hyperplasia, and early-stage breast cancer (ductal carcinoma in situ). The colorimetric output of the image pixels is compared to conventional histopathology. The results we report here support the hypothesis that histoplasmonics can be used as a novel alternative or adjunct to general staining. The widespread availability of this technique and its incorporation into standard laboratory workflows may prove transformative for applications extending well beyond tissue diagnostics. This work also highlights opportunities for improvements to digital pathology that have yet to be explored.

N, Cl-doped carbon dots for fluorescence and colorimetric dual-mode detection of water in tetrahydrofuran and development of a paper-based sensor.

N, Cl-doped carbon dots (N, Cl-CDs) were prepared by hydrothermal method from rhodamine B (RhB) and ethylenediamine (EDA). The resulting N, Cl-CDs exhibited fascinating solvent dependence and strict excitation independence. As the polarity of the solvent increased (from tetrahydrofuran (THF) to water), the emission spectrum of N, Cl-CDs was redshifted and the fluorescence efficiency decreased, which were attributed to hydrogen bond-induced aggregation. Taking advantage of these attributes, the N, Cl-CDs were used as suitable probes for fluorescence and colorimetric dual-mode detection of water in THF. The linear relationship was 0.5-100% water with the detection limit down to 0.093%. Moreover, the sensing platform was converted into a paper-based sensor for handy, real-time, and visible humidity sensing. N, Cl-CDs/PVA films were fabricated and realized continuously tunable solid-state fluorescence, further expanding their practical application.

Colorimetric cellulose-based test-strip for rapid detection of amyloid ß-42.

An innovative sensing assay is described for point-of-care (PoC) quantification of a biomarker of Alzheimer's disease, amyloid ß-42 (Aß-42). This device is based on a cellulose paper-dye test strip platform in which the corresponding detection layer is integrated by applying a molecularly imprinted polymer (MIP) to the cellulose paper surface. Briefly, the cellulose paper is chemically modified with a silane to subsequently apply the MIP detection layer. The imprinting process is confirmed by the parallel preparation of a control material, namely a non-imprinted polymer (NIP). The chemical changes of the surface were evaluated by Fourier transform infrared spectroscopy (FTIR), contact angle, and thermogravimetric analysis (TG). Proteins and peptides can be quantified by conventional staining methods. For this purpose, Coomassie blue (CB) was used as a staining dye for the detection and quantification of Aß-42. Quantitative determination is made possible by taking a photograph and applying an appropriate mathematical treatment to the color coordinates provided by the ImageJ program. The MIP shows a linear range between 1.0 ng/mL and 10 µg/mL and a detection limit of 0.71 ng/mL. Overall, this cellulose-based assay is suitable for the detection of peptides or proteins in a sample by visual comparison of color change. The test strip provides a simple, instrument-free, and cost-effective method with high chemical stability, capable of detecting very small amounts of peptides or proteins in a sample, and can be used for the detection of any (bio)molecule of interest.

A functional peptide-mediated colorimetric assay for mercury ion based on dual-modified gold nanoparticles.

In the work, a rapid and accurate biosensor for mercury ions (Hg2+) was constructed, with which aggregation of dual-modified (DGPFHR- and CALNN-) gold nanoparticles (D/C-AuNPs) could be triggered by the high specificity of peptides to Hg2+. The given peptide DGPFHR possesses great capability of capturing Hg2+, accompanied by the conformational folding. Under the circumstances, D/C-AuNPs were employed as the detection probes to accomplish the quantitative analysis of Hg2+. This is primarily because the specific Hg2+-induced folding of peptides reduces the electrostatic repulsion and steric hindrance, thus accelerating the AuNPs aggregation. The principle and application potential of this proposal was proved by evidence. And the results demonstrated that Hg2+ ions could be selectively detected as low as 28 nM with a linear range of 100-800 nM. In consideration of superior simplicity, selectivity, accuracy and stability, the protocol was advantageous over other projects in practical measurement of various water samples.